Dubbele armband van katoen

Keramiek kralen en fashion links geregen op een dubbele armband van katoen. Een zilveren vis op een nietstift met bal en bevestigd aan een ring.

1.

Undo the knot and attach a metal ring instead of the fabric ring.

2.

Pull trendy ceramic beads and fashion links onto the bracelet. “Twist” the cotton bracelet through the bead and pull it through.

3.

Put the fish onto a ball head pin and twist to form a loop.

4.

Assemble the pendant with the ring using an oval ring.

5.

Put this pendant and several more rings onto the bracelet.

6.

Gather the two fabric ends with a knot.

Zoetwater parels

Sieraden maken

Een lieflijke sieradenset met prachtige clusters zoetwater parels.

For the ear hangers attach cluster of freshwater pearls onto an ear wire. The bracelet is made by using clusters of freshwater pearls and rhinestone rondelles and threading them onto an elastic beading cord.

1

To make the tassel cut approx. 10 small pieces of leather cord.

2

Brush glue on one end.

3

Attach the pieces of leather cord into the end cap and cut to length.

Popcorn armbanden

Steenkralen en zilveren discs geregen op elastiek.

1

Pull stone beads and silver discs onto an elastic cord.

2

Tie four or five knots. Tighten well between each knot, locking the elastic cord.

Fantastisch voor sleutels

Een vet coole sleutelhanger gemaakt van een schoenveter met een metalen hanger.

1.

Snørebåndet foldes på midten og bukkes ca. 10 cm tilbage.

2.

Pull a piece of silver-plated wire through the loop of the lace as shown in the photo.

3.

Twist the silver-plated wire around the lace and tighten.

4.

Attach a pendant onto the round jump ring onto and attach the round jump ring onto the shoe lace.

5.

Start braiding – start where the silver-plated wire is twisted around the shoe lace.

6.

Always braid to the same side – i.e. always start with the same lace. This results in a twisted braiding. Finish by tying a knot.

Stone Bead Jewellery

Thread the beads onto a piece of beading wire with a bead tip and a crimp bead at each end. Assemble onto a piece of jewellery chain with round jump rings.

1

Make different sized small pieces of jewellery chain by opening a joint using two flat nose pliers.

2

Attach the pendants in the middle of a piece of jewellery chain with a round jump ring.

3

Thread the beads and the curved metal discs onto a piece of beading wire and close each end with a bead tip and a crimp bead.

4

Make your chosen number of bead pieces. Make the necklace by assembling pieces of jewellery chain and the bead pieces with round jump rings.

5

Attach the round silver pendant rings to the chain with round jump rings.

Ketting

Luxe glazen glas links geregen op een zacht leren koord gemaakt van geitenleer. Metalen links met silicone fungeren als stoppers op de ketting.

1

Cut a piece of leather cord measuring 160cm, and put a metal link with a loop in the middle.

2

Attach an eye pin in the loop of the metal link.

3

Put a glass charm bead onto the eye pin. Nip a bit off the pin and twist to form a loop in which you hang a pendant plate before closing the loop.

4

Pull a metal link onto the doubled over cord and then a glass charm bead.

5

Tie a knot at the end of each cord. Pull on two beads.

6

Pull on a link in each side and pull the opposite cord through as well, stopping the bead.

7

Glue end caps onto the cord ends.

Kleurrijke armbanden

Funky en kleurrijke armbanden gevlochten van twee schoenveters en afgewerkt met een prachtige kapittelsluiting met strasstenen.

1

Place a round jump ring (with the round clasp attached) around two shoe laces.

2

Attach the round claps to the macramé board and spread out the four shoe lace ends.

3

Start braiding by placing lace number four over number three and two.

4

Then under number two.

5

Tighten the lace.

6

Place the first lace over lace number two and three and then under number three.

7

Tighten the lace again by braiding two to each side. Continue until approx. 8cm remain.

8

Finish with a knot.

9

Now attach the other part of the toggle clasp onto a round jump ring which is then attached to the knot.

Mode

Trendy Keramieke Kralen gecombineerd met antiek zilveren Fashion Charms geregen op een zwart leerkoord. Super modieus als lange ketting met bijpassende armband.

Other Variants:

Korte ketting

Grote en kleine kralen van keramiek geregen op kralendraad. Gesloten met knijpkralen, ovale ringen en een slot.

1

A bead board is a good and practical help when making necklaces. A bead board enables you to lay all your beads out before pulling them onto the wire.

2

Pull the beads onto the wire.

3

Close in one side: close an oval ring in the swivel clasp. Put the two crimp beads onto the wire. Feed the wire through the oval ring and back through the crimp beads and squeeze the crimp beads flat.

4

Repeat in the other side, however, without the clasp. Pull the wire tight before squeezing the crimp beads. Remember to arrange the chain correctly or else it may be too tight and not “alive”.