Archief | Hobby evenementen

12091 Glas link kralen op een armband

Geschreven: 23 februari 2017 door admin

Luxe armband

Een metalen armband met echt prachtige glazen glas link kralen. We hebben ook metalen links gebruikt met silicone aan de binnenkant, zodat deze op de armband vast blijven zitten.

1

The round jump rings on the bracelet do not fit through the beads, so separate the parts by opening the round jump rings.

2

If the bracelet is too long (i.e. for children) you may use side cutters to cut off the end caps, shorten the bracelet and glue on new end caps.

3

Metal links and glass charm beads are put onto the bracelet and distributed.

4

Attach a round jump ring and – if necessary – a chain extension.

Reacties uitgeschakeld voor 12091 Glas link kralen op een armband

12253 Kettingen

Geschreven: 23 februari 2017 door admin

Met prachtige hangers

Stukken jasseron met macramé koord, metalen ketting en facetkralen aan elkaar gemaakt met ovale ringetjes.

1.

Cut a piece of thin lightly waxed cotton cord measuring approx. 4m and double it over. Cut another piece of cotton cord measuring approx. 55cm as the middle cord. Now braid for approx. 33cm. Close this piece with a knot at each end.

2.

Put a metal cone onto an eye pin and glue the cord onto the top of the cone.

3.

Put three beads onto the eye pin and twist to form a loop.

4.

Before closing the loop completely, attach two chain fragments.

5.

Attach a bead on an eye pin onto the middle of one chain.

6.

Connect the chains and attach them to a pendant with an oval jump ring.

7.

Finish the necklace by connecting it to the braided cord.

8.

Finally attach a pendant with an oval jump ring.

Reacties uitgeschakeld voor 12253 Kettingen

12048 Ringen gemaakt van veer armband

Geschreven: 23 februari 2017 door admin

Ringen met verwisselbare Glas link kralen

Ringen gemaakt van een stuk veer armband op maat geknipt en gedecoreerd met Glas link kralen of Fashion links.

De kleine onzichtbare schroefsluiting maakt het eenvoudig de Fashion links te verwisselen, zodat gemakkelijk een bijpassende ring voor een nieuwe ketting of een nieuwe armband gemaakt kan worden.

1

Cut a spring bracelet to a suitable length. Take into account the size of the fashion link you wish to use. Always start by making the ring a bit bigger as you can always cut off more of spring bracelet.

2

Thread the fashion link onto the ring and close it by screwing the two parts together. Remember to turn it slightly in the opposite direction to avoid it becoming twisted.

Reacties uitgeschakeld voor 12048 Ringen gemaakt van veer armband

11776 Trendy sieraden met keramiek kralen

Geschreven: 23 februari 2017 door admin

Armband en ketting

Kralen geregen op 2mm dik leerkoord met een gemakkelijke techniek.

1.

Double over two pieces of leather cord each measuring 75cm and tie a knot to make a loop.

2.

Thread on the beads individually onto two cords and switch between them.

3.

Gather the cords and tie a knot which fits through the loop.

Reacties uitgeschakeld voor 11776 Trendy sieraden met keramiek kralen

12249 Macramé ketting met kegels en kralen

Geschreven: 23 februari 2017 door admin

Prachtige ketting

Deze macramé ketting is gemaakt van enigzins gewaxed zacht katoenkoord met kralen. De hanger is gemaakt van een zilveren kegel en een facette druppelvormige kraal op een nietstift.

1.

Cut one piece of thin lightly waxed cotton cord measuring approx. 6m and one piece measuring approx 0.85m. Start as shown, making a double loop for a bead.

2.

Braid approx. 70cm, attaching a bead for every braided 3.5 to 4cm. Double the spacing in the middle of the necklace.

3.

Finish the necklace by attaching the last bead and tying a knot with all the cords.

4.

Make a pendant from a silver cone and glass faceted teardrop shaped bead on a ball head pin.

5.

Attach the pendant onto the necklace with an oval jump ring.

Reacties uitgeschakeld voor 12249 Macramé ketting met kegels en kralen

12049 Ketting van ketting

Geschreven: 23 februari 2017 door admin

Geweldige ketting van metaal

Maak de ringen van de ketting door de sieraden ketting te openen en in verschillende lengtes weer aan elkaar te zetten. De modieuze plastic ringen worden op de ketting geregen voordat de sieraden ketting weer gesloten wordt. Bevestig de hangers met ovale ringen.

1

Open the articulated metal jewellery chain with a darning needle by opening one joint at a time.

2

Choose your desired length and remove the rest.

3

When assembling the chain rings make sure to insert the small hooks of the chain into the holes on the first row.

4

Press in the hooks with two fingers whilst rolling the chain. Press the joint until it is completely invisible using flat nose pliers.

5

Thread fashionable plastic rings with embossed designs on before gathering the chain ring.

6

Attach a big flower pendant onto a chain ring before assembling the chain ring with other chain rings.

7

Attach a pendant with an oval jump ring.

8

Attach the closed rings before closing the chain ring. Attach pendants with oval jump rings.

9

Make the “tassel” from long pieces of chain and a closed chain ring which is then glued in place.

Reacties uitgeschakeld voor 12049 Ketting van ketting

12109 Ketting van leerkoord met facet glas kralen

Geschreven: 23 februari 2017 door admin

Ketting

Deze romantische ketting is gemaakt van een stuk 2mm leerkoord met kleine hangers gemaakt van facet en glitter kralen bevestigd op nietstiften.

1.

Place individual beads onto individual head pins. Cut off a bit of the excess pin and twist the rest of the pin to make a double loop. Remember that the loop must be large enough for the leather cord to pass through.

2.

Cut a piece of leather cord measuring approx. 125cm. Glue an end cap onto one end of the cord.

3.

Attach a pendant (approx. 8cm) onto the end cap with a large round jump ring.

4.

Tie a knot near the end of the cord. Attach three or four pendants and close with another knot.

5.

Close at the cord end in the same way as at the start.

Reacties uitgeschakeld voor 12109 Ketting van leerkoord met facet glas kralen

12279 Sierraad met vissen

Geschreven: 23 februari 2017 door admin

Zilveren vis

Dit is een prachtige ketting met hangers gemaakt op verzilverd draad en nietstiften. De hangers zijn aan jasseron bevestigd.

1.

Put beads onto an eye pin and attach this to a piece of jewellery chain by twisting the pin to make a loop.

2.

To make a pendant, put beads onto a ball head pin, twist to make a loop and twist the end of the pin around itself and nip it off.

3.

Attach the pendant onto the chain with a round jump ring.

4.

Attach round jump rings to both ends of the chain. Attach a lobster claw clasp to one of the round jump rings.

Earrings

5.

Put the silver fish onto a ball head pin. Twist to form a loop using round nose pliers and twist the end of the pin around itself and nip it off.

6.

Attach an eye pin through the loop of the ball head pin of the silver fish. Then put a bead onto the eye pin, turn the pin around itself and nip it off.

7.

Attach a French ear wire to the fish pendant by opening and closing it.

An articulated fish

8.

On a piece of 0.8mm silver-plated wire, twist to form a loop.

9.

Put the fish parts onto the wire and nip off the excess wire leaving approx. 1cm.

10.

Twist to form a loop.

11.

Attach the pendant to the chain using a round jump ring.

Reacties uitgeschakeld voor 12279 Sierraad met vissen

11695 Lava Sieraden

Geschreven: 23 februari 2017 door admin

Oorbellen

Oorbellen van lava kralen, Fashion Links, Franse oorbel haken en nietstiften.

1.

Shorten the ball head pin and make a loop.

2.

Assemble the pendant and the ear wire with a round jump ring.

Reacties uitgeschakeld voor 11695 Lava Sieraden

12112 Ketting van gevlochten leerkoord met hart

Geschreven: 23 februari 2017 door admin

Ketting

Deze ketting is gevlochten met leerkoord en afgewerkt met grote eindkappen. Een groot hart is aan de voorkant bevestigd.

1.

Cut five pieces of leather cord, each measuring approx. 50cm (they must all be exactly the same length). Double over and assemble the cord ends with a small amount of Super Attak Instant Glue prior to gluing them into an end cap. (Squeeze well).

2.

Put a small leather cord through the loop of the end cap and fasten it onto a clipboard. Put three loops onto three fingers on your left hand and two loops onto two fingers on your right hand. Keep your right index finger free.

3.

Use your right index finger to move the loop on the far left side over and down into the middle.

4.

The index finger on your left hand is now free.

5.

Now use your left index finger to move the loop on the far right side over and down into the middle.

6.

Tighten the loops on each side after each changed position of the loops. Continue to switch sides until the desired length of this section of the necklace is reached. This necklace has a 17cm plaited section between the two end caps. Do not let go.

7.

Shape the plaited section.

8.

Trim the ends and assemble with some glue. Squeeze well together and glue into the end cap. (Put the glue into the end cap and not onto the leather cords). Plait an identical section for the opposite side of the necklace.

9.

Use a piece of cord to tie a knot onto the loop of the end cap. Pull both ends of the cord through the heart.

10.

Pull the ends tight and use one cord end to tie a knot around itself.

11.

Cut off the other cord end close to the heart and push it inside. Cut off the cord with the knot leaving 3-4cm and push the end into the heart. Lock the two cord end knots with a small blob of glue.

12.

Close with an oval ring and a swivel clasp in one side and an oval ring in the other side.

Reacties uitgeschakeld voor 12112 Ketting van gevlochten leerkoord met hart