Decoratieve bal voor de tuin

Een bal van styropor met daarop glas- en spiegelmozaiek gelijmd met Paverpol lijm en opgevuld met mozaiek voeg.

1.

Divide the ball into quarters with a pencil, and then divide these into halves. Start from the line where the ball has been glued together.

2.

Start by decorating on the drawn lines. Use Paverplast which can be used for outdoor items.

3.

Then fill in the empty areas on the ball in a pattern of your choice.

4.

Next fill in mosaic tile grout. Wipe off excess grout with a damp sponge, moving it in circles. When dry, fill in any cracks with an extra layer of grout. Use vinegar to remove the  “dull” look on the mosaic tiles.

Kaart met uilen

Vivi Gade Design papier is bevestigd op de kaart met dubbelzijdig klevend tape. Bevestig de uilen met 3D foam pads.

1.

Cut a square from Vivi Gade Design Paper. It should be smaller than the greeting card. Turn the paper over and cut another square, slightly larger than the first. Glue the two squares together and glue them onto the greeting card with double-sided adhesive tape.

2.

Attach wood stickers onto the greeting card with 3D foam pads.

Prachtige ijspegels – Exclusieve Kerstdecoraties

U kunt ongelooflijke ijspegels maken met verzilverd draad en druppelvormige glaskralen. De ijspegels kunnen gebruikt worden als versiering voor de kerstboom, of aan een tak of om in het venster te hangen.

Inspirerende Video

Aangehecht bestand Klik her for at se vejledning i printervenlig version (770 kB)

1

Cut a piece of silver-plated wire which is twice the length of the desired icicle. Thread five small beads onto the wire.

2

Double over the wire and thread it outside the first bead and through the next bead.

3

Pull the wires out to each side.

4

Thread small clear beads onto one wire and continue 1/3 of the wire.

5

Repeat with the small matt beads.

6

Now thread medium sized beads (clear and matt) on 1/3 of the wire.

7

Finally thread the large beads (clear and matt) on 1/3 of the wire.

8

Twist the wire to close it.

9

Make a loop for hanging.

10

Cut off the excess wire.

11

Twist the wires around each other.

12

An icicle.

A Heart

Repeat steps 1 – 10.
Step 11: make a heart shape.

Modieuze sieraden

Een gevlochten armband gemaakt van een gekleurd leerkoord en gedecoreerd met prachtige Fashion Links.

1

Cut a piece of leather cord measuring approx. 70cm (measure your wrist, double it and add 20cm). Double over the cord and thread the charms onto the leather cord.

2

3

4

5

Cut open the loop and glue on end caps.

6

7

Tie a knot.

8

Gedecoreerde mini manden van wilg

Kleine manden met bloemen gemaakt van tissue papier uitgestanst met de Big Shot machine en in elkaar gezet met bloemendraad en een kraal.

1.

Double over several sheets of tissue paper and place them in the Big Shot machine and punch out all the parts of the  flower.

2.

Pull a bead onto a piece of floral wire and twist it to form a long stem.

3.

Assemble the tissue paper flowers onto the stem.

4.

Insert the flowers into a piece  of oasis which has been attached into the basket with a glue gun. Finally attach the small lovely dragonfly.

Decoratie met was

Wasstaven met een lont of in een wassmeltpistool worden gesmolten en het design van de zegels wordt in de was gedrukt. De zegel kan direct op het object worden gemaakt of op vetvrij papier, zodat de afdruk kan worden overgezet.

1.

In order to change the design, unscrew the top part of the seal.

2.

Light the wax stick in the wick and let drip a suitable amount of wax.

3.

Or you may use a sealing wax gun for the wax sticks.

4.

Wait for five to ten seconds until the wax has cooled down. Then push a cooled seal into the warm wax.

5.

Push down the seal for a few seconds and then remove it.

6.

You may make a wax seal on a piece of grease proof paper.

7.

The wax seal can now be removed from the grease proof paper.

8.

You may put a piece of twine into a hole made in the flap on the back of the envelope and “glue” it with wax. Then push the seal into the wax, leaving a print.